晶体锗切削温度场的理论建模及数值模拟

针对晶体锗切削加工过程,首先采用热源法及温度叠加原理建立了切削温度场的理论数学模型。然后运用MATLAB软件分别计算出切削速度分别为1.5、2.0、2.5m/s,进给量分别为0.02、0.025mm/r时工件在剪切变形区的温度场,分析了不同切削速度、不同进给量下的温度变化。最后,采用DEFORM-3D软件进行三维切削仿真分析,获得了不同切削参数下工件温度场的云图。计算结果与仿真结果表明:切削速度与进给量的增大会导致切削温度的升高,刀具与工件开始接触时,切削温度、进给量与时间呈线性急剧增加,但温度升高到一定值后会保持相对稳定。相同增量下,进给量对切削温度的影响大于切削速度。不同切削速度和进给量下的仿真结果与理论计算结果误差均小于10%。     

Soret and Dufour effects between two rectangular plane walls with heat source/sink

This study addresses the thermo‐diffusion and the diffusion‐thermo phenomena in a semi‐infinite absorbent channel whose walls are contracting/expanding, with heat source/sink effects. The governing partial differential equations with suitable boundary conditions are transformed to a system of dimensionless ordinary differential equations. An analytic solution of the problem has been found using a technique called homotopy analysis method (HAM). HAM gives consistently valid answers to the problem over an extensive variety of parameters and also provides better accuracy. To validate the analytical results, a comparison has been presented with a numerical solution calculated by using the parallel shooting method. The effects of dimensionless parameters, that is, deformation parameter, Reynolds number, Soret and Dufour numbers, and heat source/sink parameter on the expressions of velocity, temperature, and concentration profiles are analyzed graphically to understand the physics of the deformable channel. It has been noted that the velocity across the channel is higher for the expanding channel, as compared to that for the contracting channel. Also the Soret and Dufour number increases the temperature of the fluid, and decreases the concentration. The temperature profile has an increasing behavior in the case of heat source, and a decreasing behavior in the case of heat sink.     

小型煤矿低浓度瓦斯发电技术及应用效果研究

针对云南富源县辖区内大量小型煤矿抽采的低浓度瓦斯未开展有效利用的问题，以区内某小型煤矿为背景，采用现场调研、分析归纳、理论计算相结合的方法对其低浓度瓦斯发电项目展开分析研究。研究表明，某小型煤矿低浓度瓦斯发电项目成功的关键是“瓦斯治理先行”理念主导下的气源保障综合技术体系。在气源得以保障的基础上，该小型煤矿低浓度瓦斯发电项目已经持续高效运行4年，每年创造经济收益约403.2万元，减排CO2约4.47万t；同时促进了煤矿瓦斯治理工作有效落实，提高了煤矿安全生产水平，保障了煤矿产量的达标。     

Underground energy storage utilizing concrete building foundation: Experimental and numerical approach

Space heating and cooling represent 63% of total building energy demand. In the present study, the concept of concrete foundation piles was used as an underground storage medium. This system requires no additional drilling costs or space, unlike conventional boreholes. A laboratory-scaled experiment facility was designed to experimentally investigate the thermal response of a concrete pile during the charging and discharging processes. The amount of energy stored and released during each process was evaluated. A flow rate parametric study was also conducted to explore the effect of the laminar and turbulent flow behavior. In order to complement the experimental study, an extensive CFD model was developed and compared with the experimental data. There was good agreement between the numerical and experimental results for each process at different flow rates. The results revealed that increasing the flow rate increases not only the heat rejection and extraction but also the storage efficiency.     

Effect of Ni loading on SBA-15 synthesized from palm oil fuel ash waste for hydrogen production via CH4 dry reforming

The successful synthesis of SBA-15 using silica source extracted from palm oil fuel ash (POFA) was proven with the presence of mesostructure characteristics as evidenced by low angle XRD, N₂ adsorption-desorption isotherms and TEM. Different amounts of Ni were loaded on the synthesized SBA-15(POFA) using the impregnation method at 80 °C. The influence of Ni loading over the Ni/SBA-15(POFA) physiochemical properties and CO₂ reforming of CH₄ (CRM) were investigated in a stainless steel fixed-bed reactor at 800 °C and atmospheric pressure with 1:1 CO₂:CH₄ volumetric feed composition. An increment in Ni loading on SBA-15(POFA) from 1 to 5 wt% decreased the BET surface area and crystallinity of catalyst as proven by N₂ adsorption–desorption and XRD analysis. The catalytic performance of CRM followed the sequence of 3 wt% > 5 wt% > 2 wt% > 1 wt% -Ni/SBA-15(POFA). This result was owing to the even distribution of Ni and good Ni–O–Si interaction of 3 wt% Ni/SBA-15(POFA) as proved by TEM, FTIR and XPS. Lowest H₂/CO ratio and catalyst activity and stability of 1 wt% Ni/SBA-15(POFA) were due to the weaker Ni–O–Si interaction and small amount of basic sites that favor the reverse water gas shift (RWGS) reaction and carbon formation. The recent finding indicates that a quantity as small as 3 wt% Ni loaded onto SBA-15(POFA) could elicit outstanding catalytic performance in CRM, which was comparable with 10 wt% Ni loading catalysts reported in literature.     

基于AIC信息准则的Delta T声发射源定位方法

疲劳断裂是金属结构中的主要失效形式,而金属结构中的早期疲劳断裂信号通常难以检测。TOA方法是常用的声发射定位源方法,但是声波传播过程中波速变换和路径的复杂性对其结果影响很大。运用Delta T声发射源定位方法,用断铅实验模拟声发射源,用AIC信息准则对到达时间进行优化,通过使用差值求源点坐标和图像处理的方法,求得声发射源坐标。通过在平板上的实验,比较两种源定位方法在不同结构中的定位结果,分析定位误差,结果表明图像处理方法更为优秀。     

曙光煤矿1226综采工作面瓦斯抽采技术

采用综合应用理论分析、现场实测的方法,对山西汾西集团曙光煤矿1226高瓦斯综采工作面瓦斯来源进行了分析,提出并实施了分区段“风排+煤层钻孔抽放+裂隙带钻孔抽放”的联合瓦斯抽采技术。现场监测结果显示:1226综采工作面上隅角瓦斯浓度控制在0.45%~0.75%,回风流中瓦斯浓度控制在了0.44%~0.75%,瓦斯治理效果明显改善。     

Microplastics in soils: a review of possible sources,analytical methods and ecological impacts

Microplastics are emerging persistent pollutants that have been extensively detected in aqueous environments. Yet, scientists have little knowledge of microplastic pollution in soils. This study reviewed over 60 articles, with the following objectives: (i) to discuss sources and the global distribution of microplastics in soils; (ii) to evaluate current extraction techniques and analytical methods for microplastics in soils; and (iii) to comprehensively assess their adverse impacts on soils and soil organisms. Moreover, this review highlights the lack of research into microplastic contamination in soils as a significant knowledge gap. Research into the fate, sources and analytical techniques of soil microplastics and the interactions between soil organisms, soils and microplastics is essential in order to underpin management decisions aimed at safeguarding the ecological integrity of our soils. © 2020 Society of Chemical Industry     

COB LED自动在线点胶测试补粉机的研制

在COB(Chip On Board)LED光组件制造领域,点胶、测试和补粉关键工艺基本以手工或半自动为主。为了保证COB LED产品质量一致性、提高生产效率,研制了一种COB自动在线点胶测试及补粉一体机,实现点胶、测试、补粉生产工序的自动化生产。阐述了其工艺流程及设计总体方案,提出了荧光粉量修补方法,修正初次点胶量,实现动态调节,减少人工干预。经实验验证,该一体机可以提高点胶工艺的自动化程度,具有运行速度快、可靠性好、性能稳定等特点。     

综放高瓦斯矿井煤层瓦斯涌出量综合预测

为了成功预测竹林山煤矿综放高瓦斯矿井大采高工作面煤层瓦斯涌出量,以主采3号煤层为主要研究对象,针对3号煤层以往开采情况,通过布设测点测量其煤层瓦斯含量和了解相邻矿井瓦斯含量,采用分源预测法、回归法及统计法等预测方法得到了3号煤层瓦斯含量的分布规律,并绘制了3号煤层的瓦斯含量等值线图。对矿井不同生产时期的瓦斯含量进行预测,得到了生产前期、中期及后期采区的最大绝对瓦斯涌出量和最大相对瓦斯涌出量,说明了竹林山煤矿各个时期均属于高瓦斯矿井。